Jiangmen recording production: how to record + Audio post-processing experience 3

2020-06-24 327

9. Improve the shocking power of human voice.

Action - waves - L2: the parameters are as follows. When the threshold is down, the volume will be increased. The out ceiling decreases the volume downward, which is generally set to 0.3. The three boxes under the IDR on the right are 24, type1 and normai respectively. The voice is bright.

10. Pressure limit:

In order to achieve the common between words of human voice and eliminate the phenomenon of high and low, it is necessary to limit the recorded audio files. There are three methods for pressure limit. One is aa3.0 self-contained, and the other two are third-party plug-ins, one is waves C4, and the other is uitrafunk --- compressor. Let's talk about the built-in multi-stage pressure limiter. It has a variety of preset templates, which is very convenient for you to call.

Another two, C4. Click action --- derectx --- waves --- C4, find the preset pop vocol in the dialog box, click OK, and then listen to the re pressure limit until you feel satisfied. There are a lot of preset templates. Just use them.

The third one: click the function - uitrafunk - compressor to set it in the dialog box. I generally use this parameter,

Male voice: action threshold - 23.0.

Ratio: 2.0-3.0:1 for general voice.

Intensity parameters: 10 for fast songs and 30 for slow songs.

Gain 0.0: you feel the human voice is very small, but you can tune it while listening. Use it to increase the audio volume. Generally not adjustable.

江门录音制作

Start buffer: 0.1. Buffer after opening: 70. shut

Female voice: action threshold - 26.0.

Ratio: 2.0-3.0:1 for ordinary voice.

Strength parameter: 20.

Gain: 0.0.

Start buffer: 3.0. open

Buffer completed: 300. shut

There is also a pressure limiter SSLE OMP made in Britain, which is better than the above three, but it needs silver registration. We are not rich, we can use it to achieve our purpose.

After passing the voltage limit, the waveform of the whole waveform file is basically common. If the waveform is still not common, you can limit the voltage several times until you meet the requirements.

11. Recompress the voice:

Then, perform amplitude Standardization (check to adjust DC offset). Point window - amplitude diagram, there are two items to note: one is that the DC offset should be 0. Second, the total amount of RMS can not exceed - 18, and your song is good. At this point, our voice is basically done. Listen again and save the waveform file you have worked hard to make.

12. Mixed shrinkage:

Import the hard-made waveform file into the multi track form for editing. Aa3.0 will take the initiative to present your own audio in track 2. Listen to the song you sing. Is it a bit like a professional singer? Adjust the volume of accompaniment and lyrics, and click play to listen. Then click Edit - mix and shrink to the new file, and your song will be on the third track.

13. Final adjustment: still listen. Use EQ for adjustment, use self-contained, or use a third party. I use third-party. Click function - uitrafunk - EQ to set a total of three columns of data in the dialog box. 40、60、200、800、4600、15000。 1、0、0、8、08、06、06、0.5。 Third, 0.4, - 2.2, 0.3, 0.0, 6.5, 0.0, 0.0

14. Make the audio better:

Use the master processor to adjust the mixed and shrunk files. Click izoe ozone3 to set in the dialog box: there are two rows and three on one side. We can use 1, 5, 6. 1 is paragraphic eoualizer, 5 is multiband dynamics adjustment, and 6 is multiband stereo imaging adjustment.

If you can't handle the master tape well, it doesn't matter. Just use the (improvement) function in Limter, especially the audio of dance music, which is very useful.

15. Alternative recording skills:

Now there are a lot of music and dance music on the Internet, but what membership cards and gold coins do you need to download? In a word, you can only listen, not save.

Tell you a secret, use aa3. 0 can record the music and dance music for gold coins for my use. The key lies in the improper setting method of (volume control). By setting, the sound that can be made on the computer sound card can be recorded to the hard disk. The premise is that you need to install an independent sound card, which is generally OK. I use the innovative 128 sound card and spend 80 yuan. The reason is that the playback function of independent sound card is obviously better than that of version loaded sound card. Needless to say, recording takes up less resources and has a good recording function. Of course, it's better to have money to buy a professional sound card. The settings are as follows:

Check the microphone or line input if connecting to the mixer. You should try this yourself. Different sound card settings are different. Because your sound card recording jack is always connected to the mixer.

If there is no mixer in your home and the microphone jack is empty, you should check the stereo mixing option. Do not check the microphone option, and turn the volume control of the stereo mixing option to high when there is no music and to low when recording. Only in this way can the sound waveform be good. Pure sound quality. No broken sound.

Article source: Jiangmen recording production http://www.sjttv.com